Cascadiamillwork

Cascadiamillwork

Woodworking, Lumber Sawing and Building Millwork

CASCADIA TIMBER & MILLWORK CO. is a woodworking company in Eugene, Oregon. We saw logs into lumber, dry and plane it, and make wooden millwork for buildings, including doors, window frames, trim and stair parts.

Contact us Our services
About the company

Wood processing in the Willamette Valley

CASCADIA TIMBER & MILLWORK CO. was registered on April 17, 2017. The company is located at 2490 Roosevelt Blvd in Eugene, in a region of Oregon known for its forests and long woodworking tradition.

Our work covers the full path from log to finished product: sawing, drying, planing and the production of building joinery made to drawings and measurements.

EIN
93-1472859
Registered
04/17/2017
Location
Eugene, Oregon
Working hours
Mon–Fri 9:00 AM – 6:00 PM
Woodworker measuring and marking a planed board on a workbench
Services

What we do

Below is an overview of our main areas of work. Each order is discussed individually based on sizes, species and quantity.

🪵

Log sawing

Cutting logs into boards, beams and timbers of the required dimensions.

🌡️

Kiln drying

Controlled drying of lumber to a moisture level suitable for interior use.

📏

Planing and profiling

Surfacing boards and running mouldings, trim and tongue-and-groove profiles.

🚪

Doors and frames

Solid wood interior doors, door jambs and window frames made to size.

🪜

Stair parts

Treads, risers, stringers and handrails for wooden staircases.

🏠

Custom millwork

Baseboards, casings, panels and other joinery made to drawings.

Band saw cutting a Douglas fir log into boards
Lumber sawing

From log to board

Logs are first sorted by species, diameter and quality. Each log is then cut on a band saw, which uses a thin blade and leaves a clean surface with relatively little waste.

The sawyer decides how to open each log to get the best boards out of it. Lumber is cut to common dimensional sizes or to custom thicknesses and widths requested by the customer.

Drying

Why lumber is dried

Freshly sawn wood contains a lot of water. If it is used without drying, it can shrink, twist or crack later. For this reason, lumber intended for joinery is dried before further processing.

  • Boards are stacked with spacers so that air moves evenly between layers.
  • Temperature and humidity in the kiln are adjusted during the drying cycle.
  • Moisture content is checked with a moisture meter before the wood is used.
Stacked lumber in a drying kiln with a moisture meter on a board
Craftsman feeding a wooden door panel through a woodworking machine
Millwork production

Shaping, profiling and assembly

Dried lumber is planed to final thickness, then cut and shaped into parts. Moulders and shapers create profiles for trim, casings and door rails, while joints are cut for frames and panels.

Parts are then glued and assembled, sanded and checked for size. Finished items can be supplied unfinished, primed or with a clear coat, depending on how they will be installed.

Building joinery

Products for houses and buildings

Building joinery is the wooden part of a building's interior and openings. These items are usually installed toward the end of construction or during renovation.

  • Interior doors and door frames
  • Window frames and sashes
  • Stair treads, risers and handrails
  • Baseboards, casings and crown mouldings
  • Wall panels and built-in elements
Solid wood doors, window frame and stair treads in a workshop
Materials

Wood species we work with

The choice of species depends on where the product will be used, the desired appearance and the required strength. Common species in our work include:

Douglas firWestern red cedarHemlockPonderosa pineRed alderBigleaf mapleWhite oak
How we work

Steps of a typical order

Most orders go through the same stages, from the first request to the finished product.

Request

The customer sends drawings, measurements or a list of required items.

Review

We confirm species, sizes, quantities and finish.

Material

Lumber is sawn and dried, or selected from dried stock.

Production

Parts are planed, shaped, assembled and sanded.

Handover

Finished items are packed and picked up or delivered.

FAQ

Frequently asked questions

How do I place an order?

Send your drawings, dimensions and quantities to [email protected], or call us during working hours.

Do you work with private customers?

Yes. We work with builders, contractors and homeowners, including smaller orders for renovation projects.

Can you match an existing profile?

In many cases, yes. A sample piece or a clear drawing of the existing moulding helps us reproduce the profile.

What are your working hours?

Monday to Friday, 9:00 AM to 6:00 PM (Pacific Time). We are closed on weekends.

Contact

You can reach us by phone or e-mail during working hours.

CompanyCASCADIA TIMBER & MILLWORK CO.
EIN: 93-1472859
Address2490 Roosevelt Blvd
Eugene, OR 97402, USA
Working hoursMonday – Friday: 9:00 AM – 6:00 PM
Saturday – Sunday: closed
RegisteredApril 17, 2017